Do Glocks Jam? Factors and Ways to Avoid this Problem.

Introduction

Glock pistols are known for their reliability. This is a key reason why they are trusted by law enforcement agencies and militaries around the world. Their ability to perform well in difficult, high-pressure situations makes them the choice for many, but like all firearms.

Glocks are not immune to problems Including jamming. In this guide, we’ll look at why your Glock might jam, how to fix it, and what you can do to fix the problem. So you can keep your Glock running smoothly and reliably.

Poor Maintenance

It is also possible that Glock jams happen due to a lack of proper maintenance of the firearm in its parts. Glocks function through a series of interlocking parts that can attract dirt particles over time.

To avoid this, a gun owner can engage in basic maintenance practices such as cleaning the Glock and oiling its critical parts using the gun oil. Lightly coat the moving parts of the pistol with oil to keep them working properly.

Bad Ammunition

Improper or jammed ammunition is also another potential contributor to Glock jams. This can be in the form of old or rusting bullets, which have not been kept in the right conditions.

Always select high-quality ammunition for your Glock pistol but they recommend the same from known good companies. 

Weak Recoil Spring

In a Glock pistol, the recoil spring serves two purposes: it reduces the energy of the handgun backward, and it also helps to return the slide to its position after firing. In case the recoil spring gets used up and loses its strength, the slide of the Glock may have problems in moving.

This can be curbed through proper spring maintenance whereby one replaces their spring after a specified amount of time particular to them and their Glocking habits. However, this may vary with actual use and other conditions.

Improper Grip or Stance

Whenever the gun is held improperly or in any position that will end up blocking the movement of the slide, that may result in either a failure to feed or eject. 

In order to avoid this, it is wise to train oneself to assume the proper grip and stance while shooting with the Glock. 

Overly Tight Magazines

Overly tight magazines can also result in Glock jams. In other words, if the magazine does not “give” when installed, the slide would either not move at all or it would move too slowly thus causing feed or ejection failures. 

To solve this problem, ensure that the magazines are not overly far into the gun, as they should not be very tight. If there is difficulty putting the magazine inside, it is most likely that it is too tight and needs some alteration. 

Slide Lock or Locking Block Problems

Damage or wearing slide locks and locking blocks can lead to jamming issues.

If it seems this may be the case, take your Glock to a qualified gunsmith for an evaluation. This problem can be resolved by repairing elements like the slide lock level or locking block.

Why Glocks Are Known for Reliability

Glocks have gained considerable fame for the reliability of their features stemming from a simplistic design. For this reason, they have less number of moving parts which means less chance of a malfunction occurring. The polymer frame has high resistance to damage and is hard-wearing. 

Glocks are rust-resistant and have protection against oxidative wear and tear. Be it hot, cold, or any unwelcoming atmosphere, Glocks remain functional. This therefore puts them among the best for police forces, militaries, and even civilians.

How to Prevent Jamming in Glocks

When using a Glock, it is crucial to take measures to avoid inoperability. Routine care will assist in the proper functioning of the firearm and eliminate any Glock malfunctions when firing it.

Regular Cleaning and Maintenance

Ensure that you carry out regular cleaning of your Glock pistol to avoid the risk of jamming. Every machine has its moving parts that can be blocked by dirt, the edges can become blunt due to lack of Glock maintenance. Don’t forget to make the cleaning of the barrel, slide, and recoil spring to provide effective and efficient performance.

Use High-Quality Ammunition

Use only reliable and beneficial ammunition for your Glock. It is also advisable to inspect every round for imperfections before loading.

Proper Lubrication

Applying the correct amount of gun oil to your Glock is advised. If there’s not enough lubrication, then some parts will grind while there is too much oil, which will attract dirt. Use oil where there will be movement to enable movement without any pairing.

Correct Use of Magazines

Make sure that your magazine is not only free from dirt but also in a functional state. Using an unclean or broken magazine may lead to a misfeed and a failure to chamber. Use new magazines where applicable and ensure they are properly seated inside the grip.

Assess the Recoil Spring

Failure to feed properly may also be a result of an overused recoil spring. Make it a habit to inspect the spring for wear and tear after every use. Doing so will remedy failures in the proper cycling of the weapon.

What to Do If Your Glock Jams

Glock handguns are known for their durability, but jams can also occur. In the event of a jam, there are several techniques you can apply to fix the jam and bring your pistol to working condition.

Clear Jam from the Magazine by Tapping on it

Giving the magazine a few taps to the surface can help in clearing racks that are not moving, or magazines that are blocked due to some contents.

Take Apart the Magazine to Clear the Jam

If that fails, take the magazine apart to see if there is any place in it or any internal problems with the magazine that could be creating the jam.

Opening Up the Glock to Remove the Firing Jam

In case the blockage never seems to clear, attention changes to stripping down the Glock and removing other components to aid in clearing the Glock’s internal system only if you know how to do it.

Maintenance to Avoid Incurring Jams

Regular cleaning and examination of the Glock will make sure that there will not be any jams since the working tool will always be in good shape and no defects will be present.

Glock Pistol Maintenance Tips

Here are some steps that you need to follow for your Glocks Maintenance.

Step 1: Select and Buy an Optimum Cleaning Equipment

Make sure to invest in a high-quality Glock cleaning kit, with the correct sizes of tools for cleaning.

Step 2: Make Sure That the Glock is Not Loaded

In general, no cleaning has to be undertaken with a loaded weapon. The pistol chamber and the magazine should be checked for safety.

Step 3: Take Down the Gun

Break the Clock down into its parts. Glocks are fairly simple to strip and help can be found online if the manual is lost.

Step 4: Clean the Weapon

Clean the entire firearm as per the gun part cleaning solvents and brushing cleaning tools available for each gun part.

Step 5: Clean the Inside of the Barrel

Make use of a stitch bore brush and a cleaning rod to scrub clean the insides of the barrel and remove any deposits.

Step 6: Clean Every Component

Take care to clean every part of the Glock, also including the slide, frame, and recoil spring, paying the most attention to areas that are likely to have dirt.

Step 7: Pay Attention to the Trigger Area

The trigger system should also be cleaned, but do not allow any liquid to run inside as this area tends to get dirty.

Step 8: Put the Glock Together Again

When the elements are clean and dry, put together the Glock, as precision as possible, taking care to align every part in its place.

Step 9: Perform Some Light Oiling

Lastly when the pistol has been repaired, oil all steel parts within and outside of the pistol, as well as any moving parts.

Step 10: Keep in the Right Place

Put the Glock in a low moisture environment where it is not hot and not too cold to preserve it and to guard against rust.

Implementing these few guidelines will assist you in making sure that your Glock operates efficiently for many years.

Conclusion

The issue of Glock jams can be avoided through proper maintenance, quality bullets, and lubrication. In the case that there is a jam, there are methods that include tapping the magazine or removing certain parts which can be applied to fix the situation. Adhering to all these measures will help to keep your Glock in perfect working condition.